YS6 Step by Step Guide
53Pages

1. Activate your account 3 6. Install your sensors 14 2. Activate your satcom 4 7. Pair your keyfob 24 4. Pair your sensors 10 9. Disclaimer 1. Activez votre compte 29 6. Positionnement des 40 communication satellite 7 Appairez votre 50 capteurs non-responsabilité

1. Activate your YS6 account Step 1 Activate your account You will first need to download the Yacht Sentinel 6 app, you can do this by visiting the Google Play store or iOS app store or by scanning the QR code. FULL NAME MOBILE NUMBER Once downloaded, open the app and click 'Activate your account'. Enter your details and your 'Product code1 (IMEI) which is found on the back of your central unit.

2. Activate your satcom Skip this section if you did not purchase a satellite communication System. Visit www.rock7.com/register to create your account. You will then be asked to provide a 6-character product code, this can be found on the back of your rock7 unit. Click on delivery groups and add the following URL exactly to the delivery addresses: http://yachtsentinel.azurewebsites.net/service/api/ sentinel/status/v2 Once you hâve added the URL you can then add your email address. Finally click on crédits and line rental, to purchase line rental and crédits to send messages. Each...

Step 4 To power your Rock7 unit, simply plug the 2.1mm jack into the female connector. Then plug the red and blue ends into your distribution board. To plug the rock7 unit into your yacht sentinel 6, plug the téléphoné line cable into the bottom of the unit.

3. Power your unitStep 1 Attach the 3G/4G, GPS & Sensor antennain the Or order above. If you purchased the external antennas, please follow this antenna arrangement.

Be sure to place your unit on a fiat surface and position the antennas towards the bow ofthe boat. Togive power to your unit you need to plug one end of your power cable into the central unit. Then plug the positive and négative wires into your distribution board.

Step 4 Turn your units battery switch to the right to turn the central unit ON. The power LED will be amber if the YS6 is not connected to the distribution board. Your unit is up and running once the power, server and GPS LED's are green. If your units top 3 LED's are green move on to page '10'. Otherwise please move to step 6.

If your server or GPS LEDs are red, pull the power cable out of the central unit. Then turn the battery switch 'OFF'. Take the central unit outside and place it on a fiat surface, then turn the battery switch back 'ON'. After a few minutes, the server and GPS LEDs should turn green. Once they are green, take the central unit back inside and plug it back into power.

4. Pair your sensors Step 1 Unscrew the two screws on the back of the sensor. Set the central unit into pairing mode by pressing the red button and holding it down for 1 second. You will then see the sensors lightturn amber. The LED will remain amber and stay in pairing mode for 3 minutes.

Step 5 You will need to redo this process each time you want to pair a new sensor. Press and hold the pair button on the sensor until you hear a beep. After the beep you will see the LED flash green, indicating the pairing was successful. We recommend waiting 30 seconds after inserting the batteries before you try to pair the shore power or température sensors.

5. Pair your siren Step 2 Unscrew the 4 screws located on the front of the siren. Insertthe 8 AA batteries into the double-sided battery holder.

Set the central unit into pairing mode by pressing the red button and holding it down for 1 second. You will then see the sensors light turn amber. Step 4 Press and hold the pair button on the sensor until you hear a beep. Once you hear the beep the siren LED will flash green and will be paired, however, you will not be able to see it in the app or change its settings. The siren will Sound if the central unit is armed and either the high water, Motion détection and Door sensor is triggered. The siren will Sound for 3 minutes and 30 seconds. Note: In 'armed' mode, the siren will trigger even...

6. Install your sensors

Step 2 Set up your universal shore power plug by selecting your power outlet connector. Apply velcro to the back of your sensor to locate it in place.

Step 4 Connect your micro USB cable to both the universal plug and your shore power sensor. Now you can connect your universal power adapter to whichever power outlet you wish to monitor.

Step 2 Apply velcro to the back of your sensor to locate it in place.

High water sensorStep 2 Apply velcro to the back of your sensor and locate it in place. Connect the high water extension cable, then place the sensor above the automatic eut off of the bilge pump.

Ensure the prongs on the high water sensor are facing downwards.

Step 2 Apply velcro to the back of your sensor and the magnet, to locate them in place. Choose your desired location and apply another piece of velcro on your door.

Step 4 When installing, ensure magnet and sensor are positioned no more than 1 cm apart from each other. The magnet must be located on the left of the door sensor.

Step 2 Apply velcro to the back of your sensor to locate it in place. We recommend positioning the Motion détection sensor inside of the boat to avoid false détection.

◄-► 4m range Do not place directly in front of Windows

7. Pair your keyfob Step 2 Step 1 6 d «FF Once you insert the battery you will hear a beep coming from the central unit, wait 30 seconds then click the arm button on the keyfob. Once this is done, you can begin using the keyfob normally. 23A Battery (Included) Pry the case off by using the fiat head screwdriver and insert the 23A battery. Note: You may need to swipe down on the alarms page to refresh the unit State.

8. TestingStep 1 • Step 2 If ail of your sensors hâve been added correctly, click on 'Alarms' and begin configuring your YS6. Once you hâve logged in and hâve finished pairing ail of your sensors, click 'rename sensors' and check that ail of your sensors are correctly paired. The siren will not be shown in the app.